Home > Print Error > Print Error 13.01.00

Print Error 13.01.00

Create a free website or blog at WordPress.com. See Dc controller PCA. 49.XXXX PRINTER ERROR To continue turn off then on A critical firmware error has occurred that caused the processor on the formatter to abort the operation. Paper feeds from Manual Feed door fine. See Power supply. 58.3 Dc controller 1 Replace the dc controller PCA. have a peek at this web-site

We had a similar problem and changed the paper settings to accomodate card stock and that fixed it. See Printer switches and sensors, 500-sheet feeder switches, sensors, solenoids, and PCAs, or 1,500-sheet feeder switches, sensors, solenoids, and PCAs. 2 Replace the tray X pickup solenoid. 3 Replace the tray Blowing canned air on all of the paper sensors. you'll see it all.

Which can be printed from perfectly fine. Close the access door. 5 If this error persists, replace the stacker or the stapler/stacker. 13.13.00 JAM INSIDE DUPLEXER For help press A page is jammed inside of the duplexer. 1 See Formatter assembly . HP LASERJET 4250 TN PAPER JAM: MISSING PAPER-FALSE PAPER JAM Q:  We have a paper jam in our HP laserjet 4250.  We pulled out the paper but accidentally tore the paper

Pressing ( SELECT button) should clear the message. NOTE If JAM RECOVERY = OFF some pages will not be reprinted. Replace the pick-up roller if necessary (HP Part #: RM1-6323-000CN). See Dc controller PCA.

A 13.02.00 error message indicates that the media did not pass the top-of-page sensor (PS103) within the specified time. Check to ensure the tray length setting is set to the desired paper size. by unknown on Mar 17, 2009 at 6:08pm Add comment Please sign in to comment 0 we use a hp laserjet 4250/4350 at work and it prints tons of pages. go to this web-site Replace the connector if it is damaged. 5 Replace the fuser. 6 Replace the dc controller PCA.

Results 1 to 2 of 2 Thread: HP Laserjet 5200tn - getting error 13.01.00 when printing cardstock from any tray Thread Tools Show Printable Version Display Linear Mode Switch to Hybrid The output bin page-detection sensor has been active for longer than the specified time. 1 Press ( HELP button) for detailed information. 2 Press ( UP ARROW button) and (DOWN ARROW And the paper stop has a arrow on it pointing to the right position sometimes people make it to tight or it slips back slightly. Solution: 1.

Turn the printer off and then on. Do the Tray 2 rollers turn? (watch from the back of the machine with a flashlight) by Stephen on Mar 17, 2009 at 5:02pm Add comment Please sign in to comment If the separation pad is damaged, replace it. (HP Part #: RM1-6303-000CN ) If the issue persists, please contact HP Customer Support. All rights reserved.

On Sale About Us Contact Us Order Status FREE TECH SUPPORT (877) 755-5300 Login My Cart (0) Printers Printer Supplies Printer Parts Printer Accessories Error Codes Our technicians can help you Check This Out See Firmware DIMM (LJ 4200/4300 only). 3 Replace the firmware DIMM. This machine has 2 additional cassettes added onto it. biz 227 | connector hopper » Tags for this Thread 13.01.00, hp lj 4250, jamming View Tag Cloud Bookmarks Bookmarks Digg del.icio.us StumbleUpon Google Posting Permissions You may not post new

HP LaserJet Enterprise P3015 - 13.01.00, Jam in tray 2 error displayed on control panel Issue: The printer's control panel displays the following error message: 13.01.00, Jam in tray 2 Recommended tried cleaning - any ideas? See Tray 2 feed rollers (this procedure includes the separation roller). 5 Replace the dc controller PCA. Source note: There is a detent and labeling for standard media sizes.

If the roller spins freely (it should not), please contact HP Customer Support. See 500-sheet feeder control PCA or 1,500-sheet feeder control PCA. 60.4 Tray 4 lifter motor failure The tray 4 lifter-motor is not functioning. If anyone else runs into this issue be sure to follow the instruction for replacing it in your service manual as there are step that must be taken.

Using smoother paper generally results in better print quality.

See Formatter assembly . 40 EIO X BAD TRANSMISSION To continue press A connection with the card in EIO slot X has been broken abnormally. 1 Press ( SELECT button) to resume by Anonymous on Apr 6, 2009 at 12:11pm Add comment Please sign in to comment 0 Worn feed rollers-read above post to this thread-like watch from the rear or pull the See Printer switches and sensors and Fuser. 6 Turn the power off. See Laser/scanner assembly. 5 Replace the dc controller PCA.

Have you tried the settings in the paper menu? See Print cartridge. 2 Install a new HP print cartridge. 3 Check the connection between the dc controller PCA (location J97) and the memory chip on the print cartridge (location J600). PRINTER ERROR To continue turn off then on or 57.3 EP fan failure or 57.4 main fan failure X Description 3 Cooling fan, right side (LJ 4250/4300/4350 only) 4 Main cooling have a peek here See the caution and note in To initialize the hard disk. 6 If the 68.1 error persists, replace the disk. 69.X printer error To continue turn off then on The optional duplexer

Close the access door. 4 If this error message persists, replace the stacker or stapler/stacker. 13.12.10 jam in output device For help press NOTE: The event log records this error message I ran several more pages through the printer from Tray 2 and it seems to work well now. Remove the duplexer and turn the power on. A jam exists in the staple cartridge (the stapler did not finish stapling but was able to return to its home position). 1 Press ( HELP button for detailed information. 2

In some instances, electrical noise in the cable can corrupt data during transmission to the printer. See Power supply. 3 Replace the dc controller PCA. Modify your browser's settings to allow Javascript to execute. Last edited by kylebishop; 04-06-2016 at 08:13 PM.

See Formatter assembly . 5 For a 68.1 error message, reinitialize the hard disk. Table 7-7 Numerical printer messages (continued) Display-message troubleshooting 357 Control panel message Description Recommended action Y Device Location 1 DIMM Slot 1 2 DIMM Slot 2 3 DIMM Slot 3 4 See Fuser. 8 Replace the dc controller PCA. Use paper that has not been previously printed on.

Inspect the tray 3 paper-present sensor to make sure it is not stuck in the up position. See the caution and note in To initialize NVRAM. 4 If this error message persists, replace the formatter assembly. Country: United States Select a location Americas Europe, Middle East, Africa Asia Pacific and Oceania Select a language Confirm Back Z7_M0I02JG0KOT530A6KJKFRQ0816 hp-detect-load-my-device-portlet Actions ${title} Loading... If this error persists, replace the dc controller PCA.

Privacy Policy © Copyright 2016 HP Development Company, L.P. See 500-sheet feeder lifter-drive assembly or 1,500-sheet feeder lifter-drive assembly. 5 Replace the tray 4 feeder controller PCA. Use paper that does not contain metallic material such as glitter. When finished, gently install tray in printer and re-test.