Home > Print Error > Print Error 57.03

Print Error 57.03

Los Altos Hills, CA Thank you. Check the fan cable connections.2. Check and reseat connector J010 on DC Controller PCA. 3. Verify that the HP JetDirect print server has the latest firmware. have a peek at this web-site

A main cooling fan (FM1) error has occurred. DC Controller PCA malfunction.
12 OPEN or NO TONER or NO EP IIP/IIP+/IIIP Only: 1. Make sure the ink carriage latch handle is up, then reinstall the printhead. If the error persists, replace the environmental sensor (TH3). 59.XY ERROR For help press alternates with 59.XY ERROR To continue turn off then on A temporary printing error occurred. 1.

On rare occasions a defective paper control assembly or actuator can cause this problem. You might have to remove the main cooling fan to see this connection.5. If the issue persists, continue to the next step. See your browser's documentation for specific instructions. {} Z7_3054ICK0KGTE30AQO5O3KA30U5 hp-support-head-portlet Actions ${title} Loading...

The printer Toolbox opens. Verify that the correct fuser model is installed in the product. 3. Listen   for an audible “click” when the test is  nitiated. Many, such as 11 – Paper Out, may seem fairly self-explanatory but could actually be the result of something else.

Disconnect the power cable from the product, wait at least 30 seconds, then reconnect the power cable and wait for the product to initialize 2. Replace the D.C. Replace the Fan motor ( FM2 ) formatter fan.2. Verify that the fan is connected to connector J512 on the ECU PCA.

Incompatible memory card in front slot. 2. Plug the power cord back into the wall outlet. Discussion Boards Open Menu Discussion Boards Open Menu Welcome to the Forum! Step 1: Use genuine HP ink cartridges HP recommends that you use genuine HP ink or toner supplies.

Back back to top How did we do? Notify me of new posts via email. HP LASER PRINTER 3027M/30351. The values for X are listed below. ● 50.1: Low fuser temperature ● 50.2: Fuser warm-up service ● 50.3: High fuser temperature ● 50.4: Faulty fuser ● 50.5 :Inconsistent fuser (verify voltage:

Replace Laser Diode Assembly. 3. Check This Out A SIMM memory error occurred. 5Si/4000/4050/4100/5000/8000/8100 Only: X= Hardware type. 0: Rom 1: Ram Y= Hardware device. 0: Internal memory 1: SIMM slot 1 2: SIMM slot 2 3: SIMM slot We sell maintenance kits, fuser, repair parts and supplies.

Error Codes Error 10 - Supplies Memory Error 10.XX.YY Exact format is dependent on printer model The printer is unable to HP Error Code:99 - Firmware Upgrade Explanation:There has been a flash firmware failure.

Computer is powered off. 3. controller board. Clean the printhead in OS X To run the printhead cleaning tool, make sure your printer is turned on and connected to your Mac. Source Each model printer will have a slightly different wording for the error, but the trouble shooting tips are generally the same.

IIISi/4Si Only: 1. Values of XX and YY are listed below: XX00 = memory is defective XX01 = memory is missing YY00 = cartridge ● Turn the product off and then on to clear HP LASER PRINTER 3380, 3390, 33921.

If the error code still shows, try reseating the DIMMs and formatter board.

Once depleted, replace the cartridge. Obstruction in paper path. 2. Step 7: Replace the printhead Install a new printhead assembly when the existing printhead assembly is damaged or is incompatible with the printer. How did we do?

Back Error 11 - Paper Out Paper tray empty or not seated correctly. Error 21 Print Overrun The print job is to complex. If the message persists after all jams have been cleared, a sensor might be stuck or broken. have a peek here HP Error Code:59 - Motor Error Explanation:The printer has a motor error, possibly relating to the main motor, fuser motor, image drum motor or ETC motor.

Bad fuser Exit Sensor (PS3). 5Si Only: 1. To see if your product is still under warranty, go to the warranty check website http://www.support.hp.com/checkwarranty. This can happen when printing a FAX document formatted for A4 size paper.