Home > Printer Error > Printer Error 49.3007

Printer Error 49.3007

If the firmware should become corrupted or fail (usually because of an interruption when attempting to update the firmware), the product will no longer function. PDF Manual UserManual_English.pdf.... Defective Tray Size Sensing or Configuration - Most trays have tabs which depress a series of switches when installed. The chip may be missing or defective or contain incorrect information. Source

Other causes include poor quality parallel cables, poor connections, or specific software programs. Gently shake the toner cartridge both from side to side and from front to back. I am new to this and do not want to screw this up. HP color laserjet 3600 printer continue calibrating, I can't do anything.

and may not be used without advance written permission of PrinterTechs.com, Inc. 3567 Benton Street, Suite 243 Santa Clara, CA 95051 800.360.1337 408.745.9800 Order Desk: 8 AM to 5 PM Home Turn the MFP off, and then turn the MFP on. 3. Add memory to printer or reduce complexity of print job On the 5P turn the image adapt and page protect to ON or AUTO. Make sure the computer has the most current printer drivers or use a generic printer driver.5.

Replace if problem persists IIIP/IIP/IIP+ Paper feed problem - check feed/pickup rollers for movement and wear. If error persists, replace the formatter. Replace Jetdirect card and formatter board. If this firmware image is newer than the one installed on the device and the device can receive a firmware update, download the newer firmware upgrade.6.

If not replace the motor or drive circuit as required. If error persists, try printing a job from a different software application. On the II and III Series printers, this error message can be caused by a faulty paper control PCA. Reseat the PostScript SIMM and/or replace it.

XX Description 00 memory error on the cartridge or 01 memory device not found 10.00.00 Black print cartridge 10.00.01 Cyan print cartridge 10.00.02 Magenta print cartridge 10.00.03 Yellow print cartridge Supplies Home | contact Us | About Us | Terms of Sale | FAQ | HP Maintenance Kits | HP Fuser Assemblies | HP Color Supplies |HP Parts Lexmark Maintenance Kits | Veronica Casto Houston, TX It is nice to place anonline order & get to talk to an actual person. Make page less complex and retry.

John D. http://www.advancedlaser-hp-error-codes.com/error_49.htm Try a different software application and see if the job prints. The error 10 indicates a problem with the printer obtaining the information from this chip. Replace the engine controller board 49.XX PRINTER ERROR A firmware error occurred 1.

Question about Hewlett Packard Genuine HP RC17606 Fuser Assembly Fuser Assembly Fuser Unit for Color Laserjet 3000 3000n 3600 3600n 3800 3800n 110V (RM1266 1 Answer Hp color laserjet 3600n error this contact form May be feed problem. Can also indicate a mis feed or paper not being picked up. Bad drive gears.

IIISi/4Si check the door open sensor flag, PS1. Look for the conductive contacts on the cartridge and the corresponding contacts in the printer and make sure they are clean and free of contaminants. Check the Fan's connector and make sure the Fan is not blocked. 2. have a peek here if the message persists when using different software programs an attempting specific print jobs, disconnect all the cables that connect the MFP to the network or a computer. 6.

On the II and III Series and the IIISi/4Si, make sure at least one of the two drum sensitivity tabs are present. You can reseat the connectors to the scanner assembly and the control board. Turn the printer off and delete the print queue.

If it's broken, you will need to replace the sensor flag.

Go to www.hp.com/support/LJP3005 click Download Driver and software. Back back to top How did we do? A poor-quality parallel cable or network cable.3. CMYK SAMPLES 41.X ERROR Printing...

Replace D.C. Replace or clean as needed. OKI B2520 All-In-One... Check This Out You could also have a defective or dirty exit sensor.

You can try reprinting the job to see if it was a temporary error. 3. All the contacts appeared to be fine and haven't gotten any cartridge setting errors. The media that is loaded does not match the settings of the paper tray.