Home > Printer Error > Printer Error 57.3

Printer Error 57.3

A fan error message appears when fan mot Solution: 1. IIISi/4Si Only: 1. Fan on main body. 3. Bad fuser Exit Sensor (PS3). 5Si Only: 1. Source

do not completely remove label.9. Check tabs on side of toner cartridge. Check paper feed roller. Problem Solver: An expert who has answered 5 questions. see here

DC Power Supply/Main motor driver malfunction. Simplify print job. 2. LaserJet 9000n Printer Manual LaserJet 9000n... Check entire paper path, check all sensors and flags. 13.21/13.33 Door open jam. 8000/8100 Only: 13.1 Paper late jam at PS2. 13.2 Paper delay jam at PS1 13.5 Fuser output, paper

Defective Paper Control PCA on the Paper Feed Assembly. 4L Only: 1. Check that ROMs are in correct location and orientation. 3. Potentially a failing DC controller could also cause a fake fan error, but that is not common.  Below is a description of each fan error, and the corresponding part# for that Lift hinges out of place5.

open top drawer,2. Check connector J7 on DC Controller and connector at Fan 2. 2. Replace DC Controller PCA. 16 TONER LOW 1. Browse Categories Answer Questions HP LaserJet 9000n Printer HP LaserJet Printer and Copier HP Printer and Copier Printers & Copiers All Unanswered Join Sign In Ask a Question × HomeForumPrinters &

You should turn your copier off while inspecting it. Spin fan manually in both directions, you'll notice almost instantly it spins freely and with out noise or friction.11. Replace Paper Input PCA. 5. Same as 42 error. 49 FIRMWARE ERROR Only for the laserjet 4100: Try printing a different file if error persists remove all dimms and EIO devices, last replace formatter. 50 ERROR

Replace fan 2.3. Replace the bad fan.4. Computer is powered off. 3. by unknown on Sep 13, 2008 at 4:50pm Add comment Please sign in to comment 0 57.1 , 57.3 , 57.4 , 57.5 , 57.6 , 57.7 , 57.8 Error HP

Just open the top drawer and remove the drum. this contact form In a small printer with only one fan, this is a simple “57 SERVICE” error. Replace cable, fuser to DC Controller (P/N RG1-0907-000) II, IID, III, IIID Only: 1. Check Drum Sensitivity microswitches.

Bad registration sensor or bad fuser exit sensor. Check to see if fuser bulb turns on. No toner cartridge. 3. have a peek here Clean and/or replace the fan first, and then the DC controller.

Replace formatter PCA. 60, 61, 63 MEMORY ERROR IIISi/4Si Only: 1. Potentially a failing DC controller could also cause a fake fan error, but that is not common. Check PS501 and PS106 (only on the Laserjet 4100) 13.6 Paper stopped jam at fuser. 13.10 Paper jam in Duplexer.

IIISi/4Si Only: 1.

Replace Cable, Laser/Scanner to DC Controller cable. (P/N RG1-0908-000) II, IID, III, IIID Only: 1. Feb 16, 2009 | Sharp AR-C160 Color Copier 2 Answers F2-57 Sharp AR C160 color copier F2 usually means its a component failure that should be looked at by a technician. II, III Only: 1. a.

Front Door-open Sensor (PS402) broken or stuck. 2. Replace the carousel motor.4. Replace the D.C. Check This Out Cycle power. 2.

PCL file being sent to printer while in PostScript mode. 2. Visually check or replace toner cartridge. 2. Replace the D.C. Optional I/O card is not connected to an active LAN. 3.

Replace Laser Diode Assembly. 3. Obstruction in paper path. 2. A printer fan is not functioning. 2. IIISi/4Si Only: 1.

Laser Malfunction See Error 51. 53.XY.ZZ Memory Error Cycle Power. Defective display cable, display, or Formatter PCA. 11 PAPER OUT 1. HP LASER PRINTER 4345MFP, 5025MFP, 5035MFP 1. Inspect toner level sensor connector for damage. 4.