Printer Error 59.99
Yükleniyor... Çalışıyor... heiseheise 22.958 görüntüleme 5:59 TISHITU Printed circuit board (PCB) etching process by FeCl3 & Laser Printer Toner Transfer - Süre: 7:27. fastprintersdotcom 109.076 görüntüleme 4:00 Calibration for the HP 3700 Color LaserJet Printer - Süre: 1:29. at the back of the printer and then wiggle it until it falls into place. have a peek here
Replace the feed motor. (M1) Faulty DC controller PCB. Verify position of tab on top of solenoid. I printed it out and as I disassembled it, I put the parts and screws on the sheet designating its removal. Inside the unit take out Toner and Transfer unit2.
Posted on May 10, 2010 Helpful 0 Not Helpful Flag You can't post conmments that contain an email address. × Comment Anonymously Video Images Add Your Answer Tips for a great Then I reversed the order. don't know if you are a printer technician or not... Cartouche & Toner - Mr Encros 1.953 görüntüleme 2:45 Clearing a front Paper Jam on the HP 3700 Color LaserJet Printer - Süre: 0:43.
Please mark the post that solves your problem as Accepted SolutionClick the 'Kudos Thumbs Up' if this was helpful. I never bothered with the other 2 as the foam on those were OK. Do put a thin piece of stick backed felt on the solenoid as you do not want to tear it apart a second time.I fixed 2 of them this week, so https://h30434.www3.hp.com/t5/LaserJet-Printing/pls-send-about-error-59-99-ni-my-printr-color-laser-3550/td-p/2289663 There are 3 solenoids on the printer. 2 of them have foam on them that doesn't deteriorate.
Re-Assemble unit.7. Daha fazla göster Dil: Türkçe İçerik konumu: Türkiye Kısıtlı Mod Kapalı Geçmiş Yardım Yükleniyor... Oturum aç İstatistikler 9.148 görüntüleme 1 Bu videoyu beğendiniz mi? Oturum aç İstatistikler 6.791 görüntüleme 0 Bu videoyu beğendiniz mi?
Welcome Back: Visited the website for 2 consecutive days.
and This error also shows the faulty secondary transfer engaging mechanism.1. Elena by cael on Mar 24, 2015 at 8:41pm Add comment Please sign in to comment 0 I just used Moe's fix on my 3700 Color LaserjetI think the raindance was Hakkında Basın Telif hakkı İçerik Oluşturucular Reklam Verme Geliştiriciler +YouTube Şartlar Gizlilik Politika ve Güvenlik Geri bildirim gönder Yeni bir şeyler deneyin!
sensors are ok i checked it, motor is ok too, im getting out of ideas... navigate here Kapat Daha fazla bilgi edinin View this message in English YouTube 'u şu dilde görüntülüyorsunuz: Türkçe. You can change this preference below. Add × Loading...
I'll let yo know if it fixed mine as well. This is the solenoid marked SL4 in the service manual.2. I keep getting the error The configuration registry is invalid. Check This Out The magenta cartridge does not snap into position as it should because the left lock arm (?) is too low and the cartridge slips right beside it instead of going under
Add Stickiness To Your Site By Linking To This Professionally Managed Technical Forum.Just copy and paste the BBCode HTML Markdown MediaWiki reStructuredText code below into your site. HP Printers Forum Bu tercihi aşağıdan değiştirebilirsiniz. replace new tray 2 roller View Less » 8,436 people viewed this question Ask a Question Usually answered in minutes!
Also in step 13 (reinstallation tip), if tray 3 is installed, you need to press down on the big gear sticking out of tray 3 to make room for gear 2.10.
Video Photos Link Add Upload Upload × × Draw a box over the problem!! Of ALL the places to land. In step 17, note that the screw to the right is the unique screw with a thick shaft.12. this contact form The diagram looks intimidating but its not as the full hunk can be taken off and then the clutch removed for replacement.
Results 1 to 7 of 7 Thread: HP 3700dn error message Thread Tools Show Printable Version Display Linear Mode Switch to Hybrid Mode Switch to Threaded Mode 05-01-2010,12:59 PM #1 Duncan12 Error: 59.99.00 Description: An error occurred in the secondary transfer engaging mechanism. What's New? Join Us! *Tek-Tips's functionality depends on members receiving e-mail.
http://www.theofficeguide.com/toner-cartridges/faq2.html Please rate this solution thanks. Faulty feed motor. Yükleniyor... drivers, diff usb cable, it works for a while but after several test runs the error reapears.
Most likely, this problem points to an issue with the function of the DC controller: either it has failed or it has affected the developing disengaging assembly. Step 9 (removing clutch CL1) If the two screws are stuck, this can be combined with removing the Gear plate (step 12) while leaving the screws in place.5. the first time i switch solenoids, and also made an insulation for it, because the foam was totally plain, it didnt workthe second time (now) im re-making the insulation for solenoid